ZeroBloatTools LogoZeroBloatTools
Verified Preset100% Client-Side
Updated 2026-11-15•Instant Calculation

Travel Trailer WDH & Front Axle Restoral (FALR) Calculator

Pre-configured with a balanced 7,200 lb bumper-pull travel trailer behind a half-ton pickup (1,040 lb raw tongue weight, 14.44% ratio, and 60% FALR).

Interactive Pre-Configured Simulator
CAT Scale & WDH Solver
Scenarios:
Rig Dynamic Geometry & Axle Distribution
100%
PAD 1: STEER3,220 lbsPAD 2: DRIVE3,740 lbsPAD 3: TRAILER6,300 lbsTW: 1040 lbs (14.44%)
Drag to pan • Pinch or +/- to zoom
Tongue Weight (TW)
1,040lbs
14.44% of Trailer
Gross Trailer (GTW)
7,200lbs
Axles: 6,160 lbs
Trailer Sway Stability
SAFE (10%–15%)
Balanced Highway Tracking
Front Axle Restoral (FALR)
60%
Target: 50%–100% (optimal-restored)
Trailer Tongue Weight Ratio GaugeCurrent: 14.44%
▲ 14.44% (Safe)
<10% Sway
10%–15% Safe
>15% Heavy
WDH Dynamic Axle Shift:FALR: 60% (optimal-restored)
Steer Restored:+240 lbs
Drive Relieved:-380 lbs
Trailer Absorbed:+140 lbs
Scale Tickets (Lbs):
1Pass 1: Rig WITH WDH TensionedTotal: 13,260 lbs
2Pass 2: On Ball (NO WDH Bars)Total: 13,260 lbs
3Baseline: Truck Alone (Unhooked)Truck: 6,060 lbs
Vehicle Door Jamb Compliance
Truck Gross Weight (GVWR)6,960 / 7,050 lbs
98.7% Capacity90 lbs margin
Rear Axle Weight (Drive GAWR)3,740 / 4,150 lbs
90.1% Capacity410 lbs margin
Front Axle Weight (Steer GAWR)3,220 / 3,525 lbs
91.3% Capacity305 lbs margin
Receiver Hitch Tongue Limit1,040 / 1,100 lbs
94.5% Capacity60 lbs margin
Gross Combined Weight (GCWR)13,260 / 16,200 lbs
81.9% Capacity2,940 lbs margin
All Weight Limits Fully Compliant
Hitch Load & Axle Distribution Specs

3-Pass CAT Scale & SAE J2807 Restoral Breakdown (7,200 lb Rig)

Exact axle weights demonstrating how engaging Weight Distribution Hitch spring bars shifts 380 lbs off the rear drive axle.

Weigh PassSteer AxleDrive AxleTrailer AxlesEngineering Result
Pass 3: Truck Alone3,380 lbs2,680 lbs—6,060 lb baseline truck weight before hitching
Pass 2: Raw (No WDH)2,980 lbs (-400)4,120 lbs (+1,440)6,160 lbs1,040 lb raw tongue weight (14.44% of 7,200 lb GTW)
Pass 1: WDH Engaged3,220 lbs (+240)3,740 lbs (-380)6,300 lbs (+140)60% FALR restored (within SAE J2807 50–100% window)
Towing Physics & SAE J2807 Standards

Tongue Weight Ratio, Sway Stability & WDH Setup

  • When dropping a 1,040 lb trailer onto the receiver without WDH bars, the rear bumper acts as a cantilever and lifts 400 lbs off the front steering tires (3,380 -> 2,980 lbs).
  • Engaging the spring bars transfers 240 lbs back onto the front axle and 140 lbs onto the trailer axles, achieving 60% Front Axle Load Restoral (240 / 400 = 60%).
  • All five compliance checks pass with positive margins: Truck GVWR (6,960/7,050 lbs) and Drive GAWR (3,740/4,150 lbs).
Towing & Hitch Overload Hazards

Critical Errors to Avoid

Common Error: Relying on the "Dry Hitch Weight" listed in trailer brochures or manufacturer websites.
Best Practice: Brochure dry weights exclude propane tanks (60–80 lbs), dual deep-cycle batteries (120–140 lbs), front pass-through storage gear, and water. Actual loaded tongue weight is routinely 200–400 lbs higher than the brochure sticker.
Common Error: Assuming a truck can tow its maximum rated towing capacity without checking Payload Capacity.
Best Practice: Almost all half-ton pickup trucks (F-150, Silverado, Ram 1500) exceed their Payload / GVWR limit before reaching their tow rating. Tongue weight subtracts pound-for-pound from your truck’s payload capacity.
Common Error: Over-tensioning Weight Distribution Hitch spring bars past 100% FALR.
Best Practice: Over-tensioning transfers too much weight onto the front steer axle, unweighting the truck’s rear drive wheels and drastically reducing rear braking and wet-weather drive traction.
Frequently Asked Questions

Travel Trailer WDH & SAE J2807 FALR Calculator Questions Answered

What is the ideal FALR percentage for a Weight Distribution Hitch?

Under SAE J2807 guidelines, a properly adjusted Weight Distribution Hitch should restore 50% to 100% of the weight lifted off the front steer axle when the trailer was coupled unassisted.

Why did the trailer axle weight increase when I hooked up WDH bars?

WDH spring bars act like wheelbarrows lifting the rear of the truck: they push weight forward to the front steer axle (240 lbs here) and rearward back onto the trailer axles (140 lbs here).

Trailer Tongue Weight & Hitch Specifications Reference

Conventional Bumper-Pull Ideal Ratio:
10.0% – 15.0% of Gross Trailer Weight
Fifth-Wheel & Gooseneck Ideal Ratio:
15.0% – 25.0% of Gross Trailer Weight
SAE J2807 FALR Target Window:
50.0% – 100.0% Front Axle Restoral
Critical Sway Danger Threshold:
Below 9.5% Tongue Weight
Typical WDH Hardware Weight:
75 – 110 lbs (Included in Payload)
Towing Safety Notice

Towing Safety & Axle Weight Protocol

Gross Axle Weight Rating (GAWR) Limits: Never exceed the Gross Axle Weight Rating stamped on your driver door pillar. Exceeding rear GAWR accelerates tire heat buildup, risks high-speed blowouts, and overstresses wheel bearings and differential gearing.
Cold Tire Inflation Pressure: Always inflate tow vehicle and trailer tires to the maximum cold PSI listed on the vehicle tire certification placard when towing near maximum load capacity.